CivilBay                          
                             
 Home  > Concrete  > Concrete Anchorage  > Anchor Bolt Design With Tension, Shear and Moment Using Anchor Reinforcement
                                       
Skip Navigation Links                     ToolTip : 
Login
                   
ANCHOR BOLT DESIGN Combined Tension, Shear and Moment
Result Summary                  
Anchor Rod Embedment, Spacing and Edge Distance       OK  
Min Rquired Anchor Reinft. Development Length ratio = 0.86 OK  
Overall         ratio = 0.84 OK  
Seismic Design         Tension =   OK  
          Shear =   OK  
Design Code Reference                  
Anchor bolt design based on                 Code Abbreviation
ACI 318M-11 Building Code Requirements for Structural Concrete and Commentary Appendix D ACI 318M-11
PIP STE05121 Anchor Bolt Design Guide-2006 PIP STE05121
AISC Design Guide 1: Base Plate and Anchor Rod Design 2nd Ed AISC Design Guide 1  
                Code Reference
Anchor Bolt Data                    
Factored moment Mu = [kNm]            
Factored tension or compression Nu = [kN] in compression    
Factored shear force Vu = [kN]      
                   
 
                     
No of bolt line for resisting moment =            
No of bolt along outermost bolt line =            
                   
Outermost bolt line spacing s1 s1 = [mm] 102   OK   Page A -1 Table 1
Outermost bolt line spacing s2 s2 = [mm] 102   OK    
                     
Column depth d = [mm]            
                     
Concrete strength f'c = [MPa]    
Anchor bolt material   =          
Anchor tensile strength futa = 400 [MPa]         ACI 318M-11
      Anchor is ductile steel element       D.1
Anchor bolt diameter da  = [in]   = 25.4 [mm]    
Anchor bolt has sleeve   =           PIP STE05121
                   
Anchor bolt embedment depth hef = [mm] 305   OK   Page A -1 Table 1
Pedestal height ha = [mm] 431   OK    
Pedestal width bc = [mm]          
Pedestal depth dc = [mm]          
                   
                  PIP STE05121
Anchor bolt edge distance c1 c1 = [mm] 114   OK   Page A -1 Table 1
Anchor bolt edge distance c2 c2 = [mm] 114   OK    
Anchor bolt edge distance c3 c3 = [mm] 114   OK    
Anchor bolt edge distance c4 c4 = [mm] 114   OK    
                   
                  ACI 318M-11
To be considered effective for resisting anchor tension, vertical reinforcing bars shall be located RD.5.2.9
within 0.5hef from the outmost anchor's centerline  
Avg ver. bar center to anchor rod center distance dar = [mm]  
Rebar specification   =        
No of ver. rebar that are effective for resisting anchor tension nv =    
Ver. rebar size No. = 25.4 [mm] single rebar area As = 509.0 [mm2]  
Ver. rebar top anchorage option        
                  ACI 318M-11
To be considered effective for resisting anchor shear, hor. reinft shall be located RD.6.2.9
within min( 0.5c1, 0.3c2 ) from the outmost anchor's centerline min (0.5c1, 0.3c2) = 38 [mm]  
           
No of tie leg that are effective to resist anchor shear nleg =    
No of tie layer that are effective to resist anchor shear nlay =    
Hor. tie rebar size No. = 12.7 [mm] single rebar area As = 129.0 [mm2]  
For anchor reinft shear breakout strength calc    
                   
Rebar yield strength - ver. rebar fy-v = [MPa]        
Rebar yield strength - hor. rebar fy-h = [MPa]        
Total no of anchor bolt n =          
No of anchor bolt carrying tension nt =          
No of anchor bolt carrying shear ns =          
                 
                     
                 
For side-face blowout check use                
No of anchor bolt along width edge nbw =          
                 
Anchor bolt head type        
Anchor effective cross section area Ase = 391 [mm2]        
Anchor bolt head bearing area Abrg = [mm2]
         
Anchor bolt 1/8" (3mm) corrosion allowance =           ACI 318M-11
Provide built-up grout pad ?   =           D.6.1.3
                   
Seismic design category SDC >= C   =           D.3.3.1
Anchor bolt load E <= 0.2U Tensile =   Shear =   D.3.3.4.1 & D.3.3.5.1
Anchor bolt satisfies opion Tensile = Shear = D.3.3.4.3 & D.3.3.5.3
                   
Strength reduction factors                 ACI 318M-11
Anchor reinforcement fs = 0.75           D.5.2.9 & D.6.2.9
Anchor rod - ductile steel ft,s = 0.75   fv,s = 0.65   D.4.3 (a)
Concrete - condition A ft,c = 0.75   fv,c = 0.75   D.4.3 (c)
CONCLUSION
                 
Anchor Rod Embedment, Spacing and Edge Distance       OK ACI 318M-11
Min Rquired Anchor Reinft. Development Length ratio = 0.86 OK 12.5.1
Overall ratio = 0.84 OK  
Tension          
Anchor Rod Tensile Resistance ratio = 0.31 OK  
Anchor Reinft Tensile Breakout Resistance ratio = 0.15 OK  
Anchor Pullout Resistance ratio = 0.25 OK  
Side Blowout Resistance ratio = 0.28 OK  
Shear          
Anchor Rod Shear Resistance ratio = 0.57 OK  
Anchor Reinft Shear Breakout Resistance          
      Strut Bearing Strength ratio = 0.46 OK  
      Tie Reinforcement ratio = 0.69 OK  
Conc. Pryout Not Govern When hef >= 12da       OK  
Tension Shear Interaction          
Tension Shear Interaction ratio = 0.84 OK  
           
Seismic Design         ACI 318M-11
Tension Applicable       OK D.3.3.4
Seismic SDC>=C and E>0.2U , Option D is selected to satisfy additional seismic requirements as per D.3.3.4.3    
                   
Shear Applicable       OK D.3.3.5
Seismic SDC>=C and E>0.2U , Option C is selected to satisfy additional seismic requirements as per D.3.3.5.3    
Assumptions ACI 318M-11
1. Concrete is cracked D.5.2.6, D5.3.6, D.6.2.7
2. Condition A - supplementary reinforcement is provided D.4.3 (c)
3. Load combinations shall be per ACI 318M-11 9.2 D.4.3
4. Anchor reinft strength is used to replace concrete tension / shear breakout strength as per D.5.2.9 & D.6.2.9
    ACI 318M-11 Appendix D clause D.5.2.9 and D.6.2.9  
5. For tie reinft, only the top most 2 or 3 layers of ties (50mm from TOC and 2x75mm after) are effective  
6. Strut-and-Tie model is used to anlyze the shear transfer and to design the required tie reinft  
7. For anchor group subject to moment, the anchor tensile load is designed using elastic analysis D.3.1
     and there is no redistribution of the forces between highly stressed and less stressed anchors  
8. For anchor tensile force calc in anchor group subject to moment, assume the compression  
     resultant is at the outside edge of the compression flange and base plate exhibits rigid-body  
     rotation. This simplified approach yields conservative output  
9. Anchor reinft used in structures with SDC>=C shall meet requirements specified in D.3.3.7 D.3.3.7
10. Anchor bolt washer shall be tack welded to base plate for all anchor bolts to transfer shear AISC Design Guide 1
  Section 3.5.3
CACULATION                  
Anchor Tensile Force                  
Single bolt tensile force T1 = [kN] No of bolt for T1  nT1 = 2.0    
Sum of bolt tensile force Nu = S ni Ti     = 73.3 [kN]  
                   
Anchor Rod Tensile Resistance                 ACI 318M-11
  f t,s Nsa = f t,s Ase futa = 117.3 [kN] D.5.1.2 (D-2)
  ratio = 0.31 > T1 OK  
               
Anchor Reinft Tensile Breakout Resistance       ACI 318M-11
Min required full yield tension ldh ldh = 180 degree hook case = [mm] 12.5.2, 12.5.3(a)
Actual development lenngth la = hef - c (50mm) - dar x tan35 = [mm]  
        > 203 OK 12.5.1
             
              ACI 318M-11
Anchor reinft breakout resistance fs Nn = fs x fy-v x nv x As x (la / ld , if la < ld) = 503.1 [kN] D.3.3.4.5, D.5.2.9, 12.2.5
  ratio = 0.15 > Nu OK  
               
Anchor Pullout Resistance             ACI 318M-11
Single bolt pullout resistance N p = 8 Abrg fc' = 277.3 [kN] D.5.3.4 (D-14)
  ft,c Npn = f t,c Ψc,p Np = 194.1 [kN] D.5.3.1 (D-13)
  Ψc,p = 1 for cracked conc       D.5.3.6
  f t,c = 0.70 pullout strength is always Condition B D.4.3(c)
Seismic design strength reduction   = x 0.75 applicable = 145.6 [kN] D.3.3.4.4
  ratio = 0.25 > T1 OK  
               
Side Blowout Resistance              
Failure Along Pedestal Width Edge             ACI 318M-11
Tensile load carried by anchors close to edge which may cause side-face blowout        
along pedestal width edge Nbuw = nT1 x T1 = 73.3 [kN] RD.5.4.2
  c = min ( c1 , c3 ) = 125 [mm]  
  s = s2 = 406 [mm]  
Check if side blowout applicable hef = 355 [mm]          
    > 2.5c side bowout is applicable D.5.4.1
Single anchor SB resistance ft,c Nsb = = 226.9 [kN] D.5.4.1 (D-16)
Multiple anchors side blowout              
      work as group ftcNsbgw = (1+s/ 6c) x ft,c Nsb = [kN] D.5.4.2 (D-17)
Seismic design strength reduction   = x 0.75 applicable = 262.3 [kN] D.3.3.4.4
  ratio = 0.28 > Nbuw OK  
               
Group side blowout resistance ftc Nsbg =   = 262.3 [kN]  
               
Govern Tensile Resistance Nr = min ( f nt Nsa, f Nn, f nt Npn, f Nsbg ) =  234.5 [kN]  
               
Anchor Rod Shear Resistance             ACI 318M-11
  f v,sVsa = f v,s ns 0.6 Ase futa = 243.9 [kN] D.6.1.2 (b) (D-29)
Reduction due to built-up grout pad   = x 0.8 , applicable = 195.1 [kN] D.6.1.3
  ratio = 0.57 > Vu OK  
               
Anchor Reinft Shear Breakout Resistance       ACI 318M-11
Strut-and-Tie model is used to anlyze the shear transfer and to design the required tie reinft  
STM strength reduction factor fst = 0.75       9.3.2.6
               
        
               
Strut-and-Tie model geometry dv = 55 [mm] dh = 55 [mm]  
  θ = 45    dt = 78 [mm]  
Strut compression force Cs = 0.5 Vu / sinθ = 78.6 [kN]  
               
Strut Bearing Strength             ACI 318M-11
Strut compressive strength fce = 0.85 f'c = 30.4 [MPa] A.3.2 (A-3)
               
* Bearing of anchor bolt              
    Anchor bearing length le = min( 8da , hef ) = 203 [mm] D.6.2.2
    Anchor bearing area Abrg  = le x da = 5161 [mm2]  
    Anchor bearing resistance  Cr = ns x fst x fce x Abrg = 471.2 [kN]  
        > Vu OK  
* Bearing of ver reinft bar              
   Ver bar bearing area Abrg  = (le +1.5 x dt - da/2 -db/2) x db = 7480 [mm2]  
   Ver bar bearing resistance  Cr = fst x fce x Abrg = 170.7 [kN]  
   ratio = 0.46 > Cs OK  
               
Tie Reinforcement              
* For tie reinft, only the top most 2 or 3 layers of ties (50mm from TOC and 2x75mm after) are effective
* For enclosed tie, at hook location the tie cannot develop full yield strength fy . Use the pullout resistance in
    tension of a single hooked bolt as per ACI 318M-11 Eq. (D-15) as the max force can be developed at hook Th
* Assume 100% of hor. tie bars can develop full yield strength
 
Total number of hor tie bar  n = nleg (leg) x nlay (layer) = 4    
              ACI 318M-11
Pull out resistance at hook Th = ft,c 0.9 fc' eh da = 17.5 [kN] D.5.3.5 (D-15)
  eh = 4.5 db = 57 [mm]  
               
Single tie bar tension resistance Tr = fs x fy-h x As = 40.1 [kN]  
               
Total tie bar tension resistance fsVn = 1.0 x n x Tr = 160.2 [kN] D.3.3.5.4 & D.6.2.9
  ratio = 0.69 > Vu OK  
               
Conc. Pryout Shear Resistance              
The pryout failure is only critical for short and stiff anchors. It is reasonable to assume that for general
cast-in place headed anchors with hef > = 12da , the pryout failure will not govern
               
  12da = 305 [mm] hef = 355 [mm]  
        > 12da OK  
               
Govern Shear Resistance Vr = min ( fv,sVsa , fsVn ) = 160.2 [kN]  
               
Tension Shear Interaction             ACI 318M-11
Check if Nu >0.2f Nn and Vu >0.2f Vn = Yes       D.7.1 & D.7.2
      Nu / f Nn + Vu / f Vn = 1.01   D.7.3 (D-42)
  ratio = 0.84 < 1.2 OK  
               
Seismic Design              
Tension     Applicable     OK  
Option D is selected. ACI 318M-11
User has to ensure that the tensile load Nu user input above includes the seismic load E, with E increased
by multiplying overstrength factor Ωo 		D.3.3.4.3(d)
                   
Seismic SDC>=C and E>0.2U , Option D is selected to satisfy additional seismic requirements as per D.3.3.4.3    
               
Shear     Applicable     OK  
Option C is selected.             ACI 318M-11
User has to ensure that the shear load Vu user input above includes the seismic load E, with E increased
by multiplying overstrength factor Ωo 		D.3.3.5.3(c)
               
Seismic SDC>=C and E>0.2U , Option C is selected to satisfy additional seismic requirements as per D.3.3.5.3    
                   

ToolTip